A pressure washer may be a bit complicated especially when you are using it for the first time. Therefore, it is essential to know how to set up a pressure washer effectively. This article will help you to learn on how to set it up.
A pressure washer may be electric or gas driven. If your pressure washer is electric, you have to plug in the machine before using it. You can utilize an extension cord in case the pressure washer doesn’t reach the outlet. This washer is efficient and actually cleans very first, and it is fun to use it. If it is a gas-driven pressure washer, you require starting it manually. But before using it, you have to know how to set up a pressure washer. This is done by connecting the hose to the pressure washer so than you can be able to run it.
Gas washers and electric washers that have variable nozzles ought to be on low-pressure settings. Gas washers with single nozzle tip are supposed to have them removed at this juncture
First, always make sure that your water supply can carry the minimum water gallons that are specified on your pressure washer. For instance, if your machine requires 2-1/2gmp, you will need a hose that’s more than 50 feet long and not less than ¾ inch diameter that is used to connect the washer’s inlet. The first step is to rinse your hose to clean the dirt that may obstruct the water passage
Use the screws to fasten your hose on the water tank and turn it on. Let the water run for at least 30 seconds to a minute to clear out the debris that would be stuck on the inside. You need to let the water run, or it may damage your pressure washer machine.
It is always good to ensure that water isn’t obstructed throughout the whole system. Make sure that the inlet filter is clean and debris free. The other safety precaution you should take care of is the pressure of the hoses so as to avoid kickback. Prior to starting the washer, it’s essential that water is flowing all the way through the pressure washer and out the spray wand
Setting up the Hoses
Plug in the pressure washer on to the socket and switch it on. Make sure the light on the pressure washer is green in color, and if not, it means it not well grounded. Check the cord to ensure that it isn’t on the way you would like to spray. Switch on the pressure washer as you set it on the position you want to clean. We recommend that you should check that the equipment is easily grounded to avoid electrocution
Connect one end of the hose to the water inlet of the pressure washer. Place it on a flat surface that is within reach to your garden hose. The inlet port of your pressure comes with a blue labeled valve. Fasten the hose on to the port till it is tightly fastened
For some washers, the valve has to be pulled back just before you push the hose to the port. By pulling the valve in the direction of the machine, you can easily position the hose very well. Several washers are made in such a way they can use 1/2inc hose diameter.
Connect the other end of the hire pressure hose to the pressure washer outlet. The hose is usually black, and it comes with the pressure washer, and it is generally on the water inlet. Connect the end of the hose to the pressure washer pump. You can pull the port just before you connect the hose and afterward release it for it to connect on it firmly
We recommend that you don’t use the normal hose pipe instead of the hose pressure pipe because it can easily rupture. In case the pressure washer doesn’t have that pipe, you can buy it from the stores. Tighten all the connections to prevent air from entering into the lines. Fasten the end of the pressure hose to the base of the spray gun. Screw it on the valve of the gun or pull back the valve to put the pipe on its place
You can set the spray to a very low or no-pressure site to stop drawback, or any kickback, as soon as the washer has started. Turn on the water from the house tank; squeeze the spray trigger to the main pump to remove all the air from the system. Always ensure that the hose is tightly connected so that it doesn’t leak whenever you are using it. You can also fix it on the end of the spray gun
Start your pressure washer
If its gas-powered, use the pull the cord as you push it against the wheel. Let the pressure washer run for a few minutes as it warms up. It is recommended that you should never ever let the washer run for more than five minutes whenever the trigger is switched off. When the pressure washer is running, and the trigger may be locked, you can alter the setting of the nozzles making it ready to use
Once you’re done with using your pressure washer, let loose the trigger so it will not spray anymore. Then on the switch, turn off the pressure washer before you can unplug it from the outlet. Then, switch off the machine.
Whenever you stop spraying, and the pressure washer is still running, the water can drawback to the pump. This is due to the under pressure. The water passes the outlet; hence, recirculation occurs. The high pressure makes the water very hot, and it can go up to 150 degrees Celsius. This can damage your pressure washer. It is vital to know how to set up a pressure washer to get the best out of it.