This may make your once comforting swimming pool to look like a swamp. Fortunately, a pressure washer is handy and sturdy enough to clean your pool tiles from all the dirt, leaving your pool spotlessly clean. The only challenge might be just learning how to clean pool tiles with pressure washer since these pieces of equipment are so sturdy and not that simple to control.
The majority of the people usually wonder if or not you can use a pressure washer to clean your pool tiles since they are very strong. The primary concern is that the pressure washer might damage the pool tiles. Fortunately, Pressure washers can sparkle clean your pool tiles without doing any damage to them, but only if used appropriately. Pool tiles are typically made of either porcelain or ceramic, and they can be broken by a pressure washer when strong pressures are used too to clean them. That is the reason why there are methods of cleaning pool tiles with this equipment.
Clear the Pool
It is a bit easier to clean your pool tiles if there won’t be a lot of rubble along your way. You necessarily don’t have to draw off your pool for you to accomplish the job, though you will require making the water to be reasonably clean. You can make use of a handheld skimmer to pick any sticks, leaves, or other things that may be in the water. Ensure that you have cleared any dirt or debris around the area of your pool before you start too. Anything that the pressure washer may hit while you are cleaning is supposed to be moved.
Test the Pressure
After that, have a look at your user manual to find out whether it has a particular setting for use on pool tiles. Then test your pressure washer on your pool tile. It is best, to begin with, a lower setting. Begin on a single spot and spray for around 30 seconds to observe whether there is any damage. By doing this, you won’t get much of a hazard of damaging your pool tile while you are in the course of cleaning them.
If the tiles are not damaged, go on with other spots. If you see any damage while spraying or after, you may perhaps need to do it with a lower setting. You might have several changes before you get the exact spot. Also, while y testing the water pressure, you will probably need to have the heat a bit lower. It is mostly the point where you would like to ensure that the pressure won’t cause any damage. After you get on track with the real cleaning, ensure that you have turned the heat up.
Work One Section at a Time
Once you start cleaning, work in petite sections, and take your time to ensure that every area is clean before you go to the next one. It may perhaps look as if it is going to take a very long time, but this will make sure that the cleaning is more thoroughly done, and it will also keep you from returning to specific spots to clean again.
Focus first on cleaning the areas that has calcium accumulation and avoid spraying the areas with caulk joints. Then wipe out any left behind dirt or machinery. For the problematic spaces where water cannot get to, you may perhaps require to use various nozzles or any other attachment which can reach to the needed areas. You should stand far away enough from the water because it is going to be reasonably hot.
Use Less Pressure
The majority of the people usually make a mistake of using too much pressure when cleaning the pool tiles. Just use less pressure, we recommend to use, like 3,000 PSI for the task. If your pool tiles are a bit more on the delicate side still, you may use a pressure washer with low pressure, as low as 2600 PSI or again 2000 PSI though this will depend on how your situation is. Just remember first to test out your pressure to know if it is suitable. Then, make the needed adjustments.
Use the correct Nozzle
Using the incorrect nozzle might result more than strength, and thus damaging your pool tiles in the process of cleaning. We recommend you use the nozzle, which exerts the smallest amount of pressure. When buying your pressure washer, you may ask for help in picking the perfect nozzle for cleaning your pool tiles.
Keep distance from the part that you are spraying because pressure washers usually shoot very intense amounts of water. That is the reason why they cause damage to some of the tiles. For the water to be not so much intense, keep a distance from the part that you are spraying. We recommend a distance of at least 3 feet
Avoid staying in One part for Too Long
Avoid staying in one part for too long. Even though you are using the correct nozzle, or you are at the necessary distance, and you are using less pressure, spraying at one part for too long can cause a lot of damage to your tiles. Therefore, we recommend working for around 30 seconds per part, and after that, check for any damage. If the grime or algae is immovable in several areas, just spray a bit longer on those parts, but you should not spray continuously. Just spray for around 30 seconds, then stop, and afterward go at it yet again.
Pressure washing the pool tiles might be a bit challenging, especially if you are a beginner and you don’t have an idea of how it is done. Luckily, it is not that complicated. All you need to do is study these steps on how to clean pool tiles with pressure washer and also know how to evade damaging the pool tiles. Provided that you have learned about them, you ought to face no issues at all.