Paved driveways usually become a magnet for mud, oil stains, and thick grime layers. Porous concrete absorbs the stains in such a way that even water rinses and regular rain cannot get it perfectly cleaned up. While a power washer provides a quick and efficient way to remove the worst dirt, you can impeccably clean your driveway without one. Scrubbing a driveway usually takes a bit of effort and time, although it only needs to be undertaken once or twice annually to ensure your driveway is always looking great.
A perfectly cleaned driveway can profoundly improve the curb appeal. While a power washer can clean a driveway in the quickest way possible, it also needs lots of water. For those wishing to minimize the volume of water they want to use to effectively clear their driveway, other conservative methods can also be used. The best thing is to clean your driveway once per month and to maintain the immaculate appearance and prevent the stains from causing damage to the surface.
Cleaning your driveway is the quickest and most efficient way of enhancing your curb appeal. Think of it as fresh vacuuming of your yard, in a very efficient way that your visitors, neighbors, and family will definitely notice.
We have identified and outlined what you need to do to clean the concrete driveway without a pressure washer to scrub, tough stains and tidy up the driveway without using equipment that is very hard to get or water-guzzling equipment’s.
Use the paper towels to absorb oil
Sprinkle a commercial stain remover, cleaner, brake or WD-40 over the whole stain and saturate the area. Allow it to sit for about 5 minutes and then use a rag to clean it up. The good news is that using WD-40 is a sure way of making sure that your driveway is not damaged. However, if you opt to use another cleaner, you should try finding something that is biodegradable, so that you do not end up killing your plants or lawn. You could also try kitter litter, which can absorb the stain.
If you opt to use kitter litter or sawdust on the oil stains or grease, consider leaving the sawdust for approximately 12 to 24 hours to make sure it absorbs all the grease. Once done, sweep the sawdust and throw it away.
Start by removing the oil leaks from cars that had been parked in your driveway previously. A study by the University of Michigan recommended the use of kitter litter to engross these oil spills. Trickle the material on that spill from the wall perimeter to the center. Allow sufficient duration for your kitter litter to fully soak in the oil and clean it up.
At this point, you should clear your driveway. Remove the weeds developing between the cracks or slabs on your driveway. Use the broom and slate to clean up the dirt, leaves and weeds and any remaining debris.
Sweep the whole driveway to make sure that all surface dirt is removed. It is also important to make sure that you sweep out the cracks so that the swept dirt does not run down the driveway if you wash it.
Use a garden hose sprayer to spray the driveway with water.
Dissolve about 70 grams of washing soda in 4 liters of hot water. Additionally, sprinkle the dishwashing detergent over the driveway.
Dip the deck brush into the container containing the hot washing soda water and clear the driveway, rewet the brush as necessary. If you are using the dish detergent, dip your brush into a clean bucket of hot water and scrub the detergent in the pavement.
Sprinkle the grease-fighting laundry detergent or dishwashing soap over any remaining stains. Also, consider pouring in some hot water and then scrub the area thoroughly with nylon or wire brush. Repeat this step for all the stubborn stains. You can also use a commercial stain remover if the stains remain. Keep in mind that commercial stain cleaners are highly corrosive and for that reason, you ought to take the right precautionary measures to shield yourself with goggles and gloves and follow the manufacturer’s instructions carefully.
At this point, you should rinse the entire driveway with clean water until it is clean. You should avoid using the water to raise the nearby grass areas because high detergent concentration can end up damaging the plants.
How To Remove The Tree Sap From The Driveway
- Scrub the spots with the petroleum-based hand cleaner using a scrub brush or a clean shop cloth.
- Continue applying a scour and clean until the stain is completely scrubbed off.
- Sap and mop up the cleaner using the paper towels.
- Use a bucket of water or the hose to rinse the area.
- Kitter litter or sawdust
- Deck brush
- Dry dish detergent
- Washing soda
- Sprayer and the garden hose
Start by washing the driveway on the overcast days to make sure that the pavement does not quickly dry out.
If your driveway is extremely dirty, then you should consider using trisodium phosphate cleaners. Nevertheless, keep in mind that this chemical is very damaging to the nearby plants, more damaging than the detergent.
Clear your driveway of any grass, weeds or other types of vegetation growing through cracks or between the slabs in the concrete. All you have to do is pull the weeds up and clear it up. A leaf blower would be ideal for clearing debris and dirt. Using soapy hot water when cleaning the driveway is efficient is making sure that your driveway is sparkling clean after the exercise.
Now that you know how to clean your concrete driveway without a pressure washer, it should be easier for you to make your driveway stand out when your neighbors come calling.